UltraStream Undersink – Hydrogen Rich Alkaline Water Filter

Yes. Our latest version, the Mk IV, has integrated Virus Guardian technology which has NSF approval for up to 99% removal of viruses, bacteria and cysts.

Ideally, the highest H2 level is with your first glass.

No. It will reduce over the life of the filter. This is related:
a) to the suitability of your water in terms of TDS and pH
b) the intervals between uses.

Ideally you should attempt to get a glass of water, wait up to an hour, then repeat. This aligns with most people’s drinking habits and give the elemental magnesium time to regenerate more H2.

The molecular hydrogen (H₂) is generated by a reaction between the elemental magnesium of the O-Dobi media and water.
H₂ is being generated while the Ultrastream is at rest, and accumulating to its maximum even before you pour a glass. This means that the water (approx.250ml) inside the UltraStream is hydrogen-enriched and just waiting for you to pour. As new water enters the UltraStream the process of enrichment begins again.

We’ve measured output up to 1.2ppm here at Alkaway but we have to say that it always depends on the suitability of your source water, so we can’t promise a particular number. We have found that softer (more acidic) waters generate more H₂ than more alkaline input waters.

H₂ production will slowly reduce over the life of your filter as calcium accretes on the O-Dobi media. That’s one reason we use KDF media. As well as removing heavy metals and neutralising bacteria, KDF also neutralises excess hardness in input water – before the water reaches the O-Dobi.

In our design of the Ultrastream, we wanted to, where possible, reduce the waste of materials. We really wanted the stainless steel (SS) sleeve for strength and cleanliness but didn’t want to throw it away with each filter change, so we had our engineers create a removable sleeve.

When you change over to a new filter, (new replacement filters are supplied without a SS sleeve) you will need to put the old filter sleeve onto the new filter.  Removing the stainless steel sleeve video

Everyone has a different reaction to UltraStream water. It is not just ultra pure: it is also mineralised, alkaline, energised and rich in molecular hydrogen, so your body will acknowledge that there’s something happening in its hydration effect.

We’ve seen many reactions: immediate pain relief, greater urination, energy surges, a thirst for more, the feeling of silken water, detox symptoms and more. It’s good to take a note of them so you can see how the symptoms play out longer term.

An important point to keep in mind is that the most powerful water from your UltraStream will be the first glass. If you pour more than one glass, the H2 effect will lessen.

The base of the UltraStream aligns with the ON/OFF lever of the inlet tap.

Originally, our design concept was that you could alter flow rate by swivelling the UltraStream (It works – try it out!) which in turn made the base swivel.

However we found that it also caused some confusion. Users would swivel the UltraStream and their flow rate would change. They did not understand that this would happen and so we got a phone call about it.

Have a play with this function to familiarize yourself with it and make your own decision on whether you want to use it.

The UltraStream generates Molecular Hydrogen in the water without tablets.
However if you want to gain the many benefits of molecular hydrogen, without investing in an UltraStream, we recommend the AlkaWay hydrogen tablets.

For renters, we recommend the UltraStream benchtop unit. This can be fitted to most household taps/faucets and when you decide to move, it can be easily uninstalled.

Alternatively, a cheaper option is our AlkaWay alkaline water filter jug or you can look at our products here:

Our UltraStream undersink and benchtop units use the world’s best activated alumina media, removing 78% of Fluoride throughout the life of the filter. Review or download our lab test results.

Through lengthy research and development, the UltraStream uses the world’s best-activated alumina media, removing 78% of Fluoride throughout the life of the filter.
Review or download our lab test results.

Up to 95% of Fluoride can be removed when the UltraStream is installed with an additional Fluoride Pre-filter.

Attaching your UltraStream to your kitchen faucet is, in 95% of cases, easy.

1. Remove the existing ‘bubbler’ from your tap
2. Attach the included diverter to your tap.
Attach the diverter’s hose to your UltraStream.
Benchtop Installation Video

However…

Some newer faucets do not fit the thread of the diverter. In this case you have a set of adaptors that fit between the tap and the diverter.
The standard adaptor kit that is included with the UltraStream will fit most kitchen sinks

The flow diverter and adaptors are designed to fit taps with male and female threads with a diameter of 21 – 23 mm. Four adaptors are included with every new benchtop UltraStream to connect the flow diverter to different sized taps. If your flow diverter is leaking only a small amount, you can try applying Teflon tape to the thread of the adaptor ring.

If none of the provided adaptor rings fit your tap, we have the following solutions:

• We have some specially sized adaptors. To help us find the right adaptor for you, we need to see a photo with an accurate measurement of your tap or aerator (this is the part that screws off from the end of your kitchen tap).
• You could install the UltraStream under the sink using our Undersink Kit.
• A Jubilee Fitting (see photo) is a rubber fitting that can go over your faucet and secured to the tap with a metal clamp

• You could change your kitchen tap.
• You could use the UltraStream in your bathroom or laundry.

Yes, you can drink UltraStream water as you would drink regular tap water.
We have observed that the amount of water people can drink once they install their UltraStream will increase because it seems to not bloat people as many ordinary tap waters do. We aim for 8 250ml glasses per day.

Try to drink it as close to the moment it leaves the UltraStream for maximum molecular hydrogen.

This is not a problem although we wouldn’t recommend it on a regular basis. The UltraStream was not made to put hot water through it. However…

When hot water runs through the filtration media in a cheaper filter it creates tunnels. When tunnels are created the water can run through without contact with the media which means it doesn’t get filtered anymore.

We designed the UltraStream to make sure that hot water wasn’t able to tunnel. We use a  specially designed ‘spreader’ that forces the water to spread evenly which means that these tunnels just can’t happen. The negative side of any hot water intrusion is that hot water will ‘liberate’ some chlorine already accumulated so you’ll get high chlorine output while the hot water is passing through.

It is likely you have accidentally turned off the water flow at the blue and white tap on the bottom of the UltraStream.

To check to see if this is the problem:

1. Turn your UltraStream on it’s side.
2. On the bottom you will see a base plate with two holes.
3. Put your fingers into these holes and pull the base plate off.
4. Once you have done this you will see a blue and white tap.
5. You can adjust this tap to any water flow you require:
   – The flow is on full when the tap is inline with the incoming hose.
   – The flow is off when the tap is 90 degrees from the incoming hose.
   You may need to turn it off and on if it doesn’t work straight away.

OR the input hose feeding water into your UltraStream has become kinked. Follow the above instruction to check if the hose is kinked inside the base.

OR if the UltraStream is installed under the sink you may have inadvertently pushed the Grey JG Converter in too far.

In this case, please do the following as soon a possible:

1. Turn off the cold water connector under the sink.
2. Use the ‘John Guest’ spanner and take out the Grey ‘John Guest’ Converter on the top of the UltraStream. Check to see if you have the clear plastic tubing on the stem.
3. Replace it with the spout.
4. Put water through the UltraStream by turning the cold water connector back on (make sure you have the UltraStream on the sink of have a bucket for the water to flow into)
5. If the water starts to flow again don’t reinsert the old Grey ‘John Guest’ Converter.
6. Phone AlkaWay for a new Grey ‘John Guest’ Converter to replace your old one.

OR if the above doesn’t work then it may have blocked up prematurely due to a municipal pipe flush which creates a lot of sediment in the water, or you may be overdue for a new replacement filter.

This is NOT air, it is the Molecular Hydrogen which is a gas.

The spurting happens because Molecular Hydrogen has built up in the UltraStream overnight and/or when it hasn’t been used for a while.

The first water that comes out of the UltraStream is the best as it will have the most of this anti-oxidant and anti-inflammatory quality.

If you want to get the most Molecular Hydrogen from your water drink it fresh, straight from the UltraStream.

It is like an orange; when an orange comes fresh off the tree and it is cut in half, it has its highest anti-oxidant quality.  Leave the orange just sitting open and the anti-oxidants leave the orange.

Put the orange in a sealed container in the refrigerator and the anti-oxidants will last much longer.

Like an orange, if you can’t drink your UltraStream right away, store it in a sealed, preferable glass or steel container, and if possible, in the refrigerator.

The standard adaptor kit that is included with the UltraStream will fit most kitchen sinks

The flow diverter and adaptors are designed to fit taps with male and female threads with a diameter of 21 – 23 mm. Four adaptors are included with every new benchtop UltraStream to connect the flow diverter to different sized taps. If your flow diverter is leaking only a small amount, you can try applying plumber’s tape to the thread of the adaptor ring.

If none of the provided adaptor rings fit your tap, we have the following solutions:

• We have some specially sized adaptors. To help us find the right adaptor for you, we need to see a photo with an accurate measurement of your tap or aerator (this is the part that screws off from the end of your kitchen tap).
• You could install the UltraStream under the sink using our Undersink Kit.
• A Jubilee Fitting (see photo) is a rubber fitting which can go over you faucet and secured to the tap with a metal clamp

• You could change your kitchen tap.
• You could use the UltraStream in your bathroom or laundry.

Yes, the UltraStream is vegan, the fluoride reduction media in the UltraStream is not bone char.

The special magnesium O-Dobi beads react with two water moclues to produces magnesium hydroxide and hydrogen gas.

Mg ＋ 2H₂O  →   Mg(OH)₂ ＋ H₂

The Hydrogen gas isn’t very water soluble so it’s a good idea to drink the water quick to get the maximum amount of molecular hydrogen.

KEY
Mg = Magnesium Metal
H₂O = Water
Mg(OH)₂ = Magnesium Hydroxide (often called Milk of Magnesia)
H₂ = molecular hydrogen (Hydrogen Gas)
H = Atomic Hydrogen (Active Hydrogen)

The warranty for the UltraStream is 3 years (Conditions Apply) for parts and labor under normal use. Warranty does NOT cover filters as there are too many variables in the source water.

Unlike electric water ionizers, the UltraStream’s filter cartridge actually contains the media that ionizes, alkalizes and infuses the water with molecular hydrogen. So when you change a filter, you get the brand new version, which will incorporate any updated technology we have implemented. That’s why we call it an ‘eternal’ system.

The only consideration is for those taking pharmaceutical medicine or suffering from kidney disease. We recommend you consult with your doctor.

UltraStream water may be delivered to the cells more efficiently than tap or bottled, so we recommend not taking any medications with it. We suggest you stop drinking 30 minutes prior to taking the medication and then waiting until at least 30 minutes after.
We have no evidence of adverse results, but give this advice for legal purposes only.

It is a selective antioxidant. It targets and neutralizes the harmful, cytotoxic free radicals, such as hydroxyl radicals.

• It helps people feel better, perform better and enjoy a healthier life.
• It is easy to install, operate and replace the filter.
• It is affordable, benchtop costing 75 cents/gallon for the first year and then down to 31 cents/gallon on your 12 month filter change (benchtop version).

Our independent laboratory tests used a water sample that was a ‘witches brew’ of pesticides, volatile organics, fluoride, chlorine, heavy metals, and minerals. The UltraStream changed an input pH of 7 to an output pH 9 in these tests. We’ve pushed the lab much farther than the normal lab tests by asking for performance statistics beyond the normal lifespan of the filter. Most water filter tests are taken from the first water out of the filter. Most do not test for a possible reduction in performance as the filter is continued in service.

Review or download the UltraStream Test results

UltraStream’s pH performance is directly related to the input water. Tap water is the only regulated water in the US and is around pH 7.0 for most homes. The UltraStream performs wonderfully in this environment and will consistently produce water ranging from pH 8.0 – 9.0. Most commonly, the water starts at pH 9.0 at installation, and by the time the filter needs to be replaced, it measures closer to pH 8.0. The bottom line: more acidic input water will have a lower pH, more alkaline input water will have a higher pH but both may be adjusted using the flow control at the bottom of the UltraStream.

There are a couple of other advantages as well. In hard water with excessive levels of alkaline minerals (like an overabundance of calcium), the UltraStream uses a special patented media that alters the form of the calcium and prevents it from clogging the filter. It also re-infuses input water with healthier levels and proportions of alkaline minerals, as well as ionizing the water.
We’ve used our two decades of water filter experience to ensure this lasts the life of the filter, so you have excellent purity and performance from start to finish.

Those who utilize well water should also expect great performance. Very often, well water starts a bit above 7.0 and this can also translate to higher pH outputs from the UltraStream as well. A sediment pre-filter will likely be required for well water.

Yes, unlike electric water ionizers, the UltraStream will also work well with a water softener.

Softened water isn’t something you want to drink or cook with, so the UltraStream is a great solution for consumption when you need to maintain soft water for appliance life and showering.

Yes, the UltraStream can be connected in series with a reverse osmosis (RO) system with the vented faucet we can supply. It will add powerful alkalizing and ionizing abilities to your acidic, mineral-depleting RO water.

You could also remove the RO system completely and replace it with the UltraStream.

Yes. Through lengthy research and development, the UltraStream uses the world’s best-activated alumina media, removing 78% of Fluoride throughout the life of the filter. Review or download our lab test results.

Up to 95% of Fluoride can be removed when the UltraStream is installed with an additional Fluoride Pre-filter.

An UltraStream filter will last 12 months – depending, as always, on source water conditions and use. Our 12-month recommendation is based on a family of 4, who use about 2.1 gallons per day (8 glasses / 65 fluid oz each) for drinking and cooking.

If you use less, your filter may last longer. More – and you’ll need to replace sooner.

Filter life always depends on the quality of the input water. The more unwanted stuff in the water, the harder the UltraStream has to work. For the vast majority of users, 12 months of protection and performance is no problem.

When the filter is replaced (a simple 3-minute job) your UltraStream returns to full filtration, pH, hydrogen and antioxidant power.